Stereotomy

The art of representing objects in section, elevation and plan in order to cut them out. - Louis Mazerolle

Thursday, September 29, 2011

devers de pas (2)

In the first post in this series, I introduced the "devers de pas" method and gave an example of its use. Now we will see how to construct the footprint at ground level in a few different situations. In future posts I will cover more complicated cases.

Our plan is the same as we used in the first post.

This shows a trapezoidal ground plan and a cross section of the roof at the principal rafters, which are placed points E and F. The result will be a pyramid with the faces meeting at the highest point, K. We draw in the ridge lines where each face meets its neighbor:

and take a look at the situation in 3D:

The left and right (looking from the top) roof faces have the same slope, but the top and bottom faces are at different slopes.

We are going to run rafters along all the faces and all the ridge lines, with different cross sections too. We will assume that each rafter goes all the way to the peak of the roof, even though that would produce an impossible traffic jam. Once we've found a timber's footprint, we will show it in 3D with the top sawed off. We will first find the footprint of the principal rafters:

This should be pretty easy. The top and bottom edges of the footprints are already shown on the plan: those are the vertical faces of the rafters. In order to find the inner edge of the footprint, we need to look at the elevation drawing. We find the point where the inner edge of the rafter intersects the ground plane, and run it down into the
plan:

and we get the footprint in fuchsia. Next, we will erect a rafter from point H up to the peak, with the same width and depth as the principal rafters:

This rafter has plumb faces too and won't be much harder. The only problem is that we don't have an elevation view of this roof surface. So, we construct one using the height h of the roof peak:

We constructed the elevation right over the plan. This is common in the French carpentry drawing tradition. It saves space, which is important if the plan is drawn at full scale (called an "épure".) It also allows us to easily move between the plan and the elevation. Again, the inner surface intersection line gives us the inner edge of the footprint.

When we set out to find the "dévers de pas" line that defines the side of a footprint, we are really looking to define the plane for that side of the timber. In order to draw the line on the plan, we need to connect two points that lie on both the timber's side and the ground plane. We usually have one point in hand already: The point where the side meets the roof gutter line. So, the problem often reduces to finding one more line in the side plane and its intersection with the ground.

Consider the principal rafter rising from point E. The rafter's sides are square, so if we drop a perpendicular line from a point on the top edge, it will lie in the side face:

Since the upper surface of the rafter lies in the surface of the roof, that line is a surface normal, and is parallel to all other surface normals of that roof:

This is good stuff. If we need a line for our dévers de pas construction, we just need to look for a surface normal somewhere.

Next, erect a rafter from G up to the peak. This is our skewed rafter from the first post:

We are not going to construct the projection line directly on the side of the footprint yet. Instead we will construct a parallel plane -- and D.P. line -- starting from G because that works better with our principal reference point, the peak of the roof at K. That plane contains the line from G to K; we are looking for one more line to completely specify it.

As before, we start with an elevation view of this roof surface. We can use the roof height, but the view needs to be along the roof line. We do that by running a line perpendicular to the roof edge through K and forming a right triangle with the roof peak height, taking us to point M:

If you tilt your head over to the side, you are looking at the elevation view of rafters in this roof surface. Even if a rafter doesn't rise square from the gutter line, it will usually be kept between the upper and lower surfaces shown in this view. If we cut out the elevation view and tip it up in 3D, we can see what's going on:

Now, draw a perpendicular line to ML at M and mark the point where it intersects our baseline KL as "Q":

A perpendicular line dropped from surface in an elevation view is very common and is labeled "T.C." for "trait carré" or square line. Let's also flip that into 3D:

Now it becomes obvious why the T.C. line is so important: it's normal to the roof surface. Therefore it lies in the plane passing through G that we are searching for:

So we can draw the dévers de pas line in our drawing:

and fill in the footprint of the rafter. We give the rafter a width along the gutter line and use the inner surface intersection from the rafter elevation, as before:

In the final 3D view, we see how the plane we constructed is parallel to the sides of the rafter:

This construction that uses a surface normal in the form of the "trait carré" to derive the D.P. line is used again and again in Mazerolle's drawings.

P.S. Chris Hall has a go at the same model in this post. Check it out; it was one of my inspirations for learning more about this French method and Louis Mazerolle's works.

6 comments:

  1. Tim,
    This posting was really great.
    For those who would like an instructive exercise:
    go to Chris' version (see link "this post" above) click to enlarge the FIRST figure and print it out in monochrome. Now take some coloured pens/pencils and trace Tim's construction for rafter G on the print-out - its all there !
    It gives me hope I can make sense of LM...
    Greetings.

    ReplyDelete
  2. This comment has been removed by the author.

    ReplyDelete
  3. Hey Tim,

    I'm in the process of writing a Google SketchUp Ruby Script Plugin for a Trapezoidal Ground Plan after reading through your pages on dévers de pas.

    Here's what I got so far
    Depth of rafters were determined from the plumbcut of the principal rafters.
    http://www.sbebuilders.com/Traite_De_Charpente/Depth_of_Rafters.jpg
    http://www.sbebuilders.com/Traite_De_Charpente/Depth_of_Rafters_dialog.jpg

    http://www.sbebuilders.com/Traite_De_Charpente/Trapezoidal_Ground_Plan_dialog.jpg

    http://www.sbebuilders.com/Traite_De_Charpente/Skewed_Rafter_Peak.jpg

    http://www.sbebuilders.com/Traite_De_Charpente/Dim_Angles.jpg


    Sim

    ReplyDelete
  4. Hi Sim,
    You are on the right track. I say more about the depth of rafters in http://stereotomy-blog.blogspot.fr/2011/10/devers-de-pas-4.html. At this point I was unclear on the concept; Chris straightened me out :)

    Your plugin looks very cool.

    Tim

    ReplyDelete
  5. Great site! HH Seigele and Fred Hodgson were drawing such configurations as these for American Builder and The Carpenter magazines at the turn of the 19th-20th C but with no explanation other than "...do this, now that". So great to see your super lucid explanations. Many thanks

    ReplyDelete